Furman M-8×2 15A Standard Power Conditioner


Furman M-8×2 15A Standard Power Conditioner



Install an M-8×2 in to the top slot of your rack, and the eight switched outlets in the rear panel will power up and protect all your equipment up to a 15-amp load.

A Merit Series Power Conditioner is the perfect low-cost AC power solution for any rack mount system. The M-8×2 is designed for applications where lights are not required.



You`ve got a rack for your effects, preamps, tuner…You`re going to plug that into the wall? One big spike and your rig is up in smoke. Furman`s standard level surge/spike protection defends your gear from the spikes and surges that are so common at gigs and practice spots. With Furman`s standard level RFI/EMI filtration, you`ll get a quieter tone without pops, crackles, and the local radio station coming out of your amp.


Can`t track down where that noise is coming from? Your mix sounding flat? With Furman`s standard level RFI/EMI filtration you`ll lower the noise floor caused by the dirty AC power coming into your console or DAW. Furman`s standard level surge and spike protection keeps your sensitive digital equipment from acting funny or burning up due to everyday spikes and surges. With a 15A capacity and nine total outlets, it`s enough to power your whole home studio.


Bars, clubs and other event venues have some of the worst power out there – from air compressors turning on and off to light shows pulling current loads up and down, the AC power can be a strain on the circuits in your rig. Furman`s standard level protection and filtration keeps the bad stuff out.


When you`re out there gigging, you never know what kind of power you`re going to get.

The wear and tear on mobile rigs eventually takes it toll – that`s why it`s smart to plug into Furman`s standard level protection and RFI/EMI filtration. It keeps your equipment safe and sounding clean. Whether you`re setting up a show at the local club or powering up the church band for their next service, make sure you give them power they can trust.

Furman M-8X2 Features at a Glance

Noise Filtration

AC noise filtering to reduce radio frequency and electromagnetic interference (RFI/EMI)

Surge Protection

Spike & surge protection ensures equipment stays safe and your power stays clean

9 Total Outlets

8 rear panel outlets and 1 front panel outlet

15 Amp Rating

15 amp rating, with circuit breaker

“Protection OK” Indicator

Front panel indicator LED lets you know that your equipment is being protected

Wall Wart Spacing Indicator

Rear outlets have been spaced to accommodate even the bulkiest of wall warts and adapters

Furman M-8X2 Specifications


Family Merit Series

Line Voltage 120 (Volts)

Number of Outlets 9

Number of Isolated Banks 0

Outlet Descriptions All 9 outlets filtered and surge protected

Rack Mountable Yes

Rack Ears Included Yes

Front Panel Meter(s)No

Front Media Light(s)No

Control Front panel:

– On/Off switch

Voltage Regulation No

Compliance cTUVus

USB Charging N/A

Low Voltage Trigger N/A

AC Power Cord 6 ft. captive, 14 AWG, with 3-conductor Edison Plug

Dimensions 19″ W x 3.75″ D x 1.75″ H

Weight 4.9 lbs

AC Protection

AC Protection Technology Standard spike and surge protection

Under-Voltage Shut off N/A

Maximum Continuous Operating Voltage 130 VAC RMS

Maximum Current Rating 15 (Amps)


Filtration Technology Standard Level RFI/EMI Filtration

Filtration Rating

Greater than 23dB, 200Khz to 10 Mhz

Shipping Info

Length 21.9 (Inches)

Width 6.5 (Inches)

Height 3.4 (Inches)

Weight 4.8 (Lbs)

Other Specifications

Spike Protection Modes:Line to Neutral

Energy Dissipation:150 joules

Peak Impulse Current:12,000 amps

Construction:Steel Chassis, Black Painted.